User manual ZANUSSI ZDI111X

[. . . ] 156997390en. qxp 1/17/2007 3:17 PM Page 1 User manual Dishwasher ZDI 111 156997390en. qxp 1/17/2007 3:17 PM Page 2 Content Safety information - - - - - - - - - - - - - - - - - - -3 Control panel and functions - - - - - - - - - - - -4 Programme table - - - - - - - - - - - - - - - - - - -6 Before the first use - - - - - - - - - - - - - - - - - -6 Setting the water softener - - - - - - - - - - - - -7 Filling with dishwasher salt - - - - - - - - - - - -8 Filling with rinse aid - - - - - - - - - - - - - - - - - -9 Adjusting the dosage of rinse aid - - - - - - -10 Loading cutlery and dishes - - - - - - - - - - -10 Filling with detergent - - - - - - - - - - - - - - - -12 Unloading the dishwasher - - - - - - - - - - - -13 Cleaning and care- - - - - - - - - - - - - - - - - - 13 Environmental concerns - - - - - - - - - - - - - 14 Something not working - - - - - - - - - - - - - - 15 Technical data- - - - - - - - - - - - - - - - - - - - - 17 Consumption values - - - - - - - - - - - - - - - - 17 Hints for test institutes - - - - - - - - - - - - - - - 18 Installation - - - - - - - - - - - - - - - - - - - - - - - 18 Guarantee/Customer service - - - - - - - - - - 21 European Guarantee - - - - - - - - - - - - - - - - 23 2 156997390en. qxp 1/17/2007 3:17 PM Page 3 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. Correct use This dishwasher is only intended for washing household utensils suitable for machine washing. Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket. [. . . ] Switch off the dishwasher, open the door and carry out the following suggested corrective actions. Fault code / malfunction The dishwasher does not fill with water. - continuous flashing of the start/cancel indicator light - 1 flash of the "end of programme" indicator light The dishwasher will not drain. - continuous flashing of the start/cancel indicator light - 2 flashes of the "end of programme" indicator light - continuous flashing of the start/cancel indicator light - 3 flashes of the "end of programme" indicator light The dishwasher door has not been properly closed. The water inlet hose has not been correctly laid or it is bent or squashed. The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. Close the water tap and contact your local Service Force Centre. Close the door Insert the mains plug The fuse has blown in the household Replace the fuse. If dishes are to be washed immediately, cancel the delay start. Once these checks have been carried out; close the door, switch on the dishwasher and press the start/cancel button. The programme will continue from the point at which it was interrupted. If the malfunction or fault code reappears contact the Service Force Centre. For other combinations of fault codes not described in the above chart, please contact your Service Force Centre. 15 156997390en. qxp 1/17/2007 3:17 PM Page 16 The wash results are not satisfactory The dishes are not clean The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. The spray arm do not rotate freely due to wrong arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Where there are limescales deposits on the dishes; the salt container is empty or the wrong level of the water softener has been set. The salt container cap is not properly closed. The dishes are wet and dull There are streaks, milky spots or a bluish coating on glasses and dishes Water drops have dried onto glasses and dishes Rinse aid was not used. The detergent may be the cause, Contact the detergent manufacturer's consumer care line. If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model (Mod. ), product number (PNC) and serial number (S. N. ). This information can be found on the rating plate located on the side of the dishwasher door (see picture). So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. . 16 156997390en. qxp 1/17/2007 3:17 PM Page 17 Technical data Dimensions Width Height Depth. 59, 6 cm 81, 8 - 87, 8 cm 57, 5 cm Electrical connection Voltage - Overall power - Fuse Water supply pressure Capacity Max. weight Noise level Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher's door. Minimum Maximum 0, 05 MPa 0, 8 MPa 12 place settings 38 Kg 51 dB (A) Consumption values The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes. Programme INTENSIVE 70°C NORMAL 65°C 65°C A 30' BIO 50°C (Test programme for Test Institutes) RINSE & HOLD Programme duration (minutes) 120 - 130 100 - 110 30 140 12 Energy (kWh) 1, 8 - 2, 0 1, 4 - 1, 6 0, 9 1, 05 < 0, 1 Water (litres) 22 - 25 19 - 21 9 16 5 17 156997390en. qxp 1/17/2007 3:17 PM Page 18 Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values"). [. . . ] Connected damage caused by these removal and replacement operations will be the responsibility of the user. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair costs are considered disproportionate, in agreement with the consumer, the defective appliance may be replaced with another appliance of the same value. In this event, we reserve the right to ask for a financial contribution calculated according to the length of time it has been used. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a new guarantee period begins. [. . . ]