User manual ZANUSSI Z5531

[. . . ] The glass cover (only on some models), before lighting the over burners of the top and until their turning off, shall be in open position; it is important to avoid any contact with cookware during the cooking in order to save from a dangerous overheating. MODELS SPECIFICATIONS Fig. 1 a2 B a1 100 a2 C1 C2 B a1 100 Important After the cooker use it is recommended to: 1) always check that the knobs are in the " " position. 2) close the cock of the gas cylinder (if you use liquefied gas) or the supply cock (in case of natural gas). 3) periodically check the wear of the hosepipe and replace it if necessary. [. . . ] The grids and burners can be taken away and easily washed in warm water and soda. While it is still warm clean with a cloth soaked with warm water and detergent, followed by a careful rinsing and drying. The bottom of the oven can be easily extracted and washed in the washbasin together with dripping-pan and gridiron shelf. IMPORTANT: Check the wear of the gas hosepipe connecting the cooker to the cylinder and replace it in case of anomalies. It is recommended to change it yearly; in any case within the date impressed on the hose. The replacement of spare parts and maintenance operations shall be carried out by qualified personnel only. 15/b). GREASING THE THERMOSTAT VALVES In case a cock is blocked or stiff during the turning, it is necessary to change the grease as follows: - Close the on-off valve of the gas system or cylinder. 11) - Take away the burners caps, caps and support grids - Lift up the cook-top - Unscrew the screws of the control panel and remove it. 15/B 5 USE OF ACCESSORIES Timer Your range can be fitted with this accessory that you can wind by rotating the corresponding knob clockwise by one complete turn and set the pointer to the desired cooking time (expressed in minutes) by rotating the knob counterclockwise. Electric timer Your range can be fitted with this accessory acting both as a clock and as a timer as well. To set minutes rotate the small knob counter clockwise without pushing it. Automatic working mode (postponed cooking start time) First you should set your cooking time (both the "AUTO" and the symbols will lit up) and then the cooking end time, the symbol will switch off as previously stated. When cooking time has run out, the symbol will switch off while the "AUTO" symbols flashes and the acoustic warning signal starts. Manual working Manual working is possible only after having cleared the automatic program by pushing button 3. Acoustic warning signal The acoustic warning signal starts at the end of a program and lasts about two minutes. Program start and check Program starts after about 4 seconds from the setting. It is possible to check the set program at any time by pushing the corresponding button. Correction and cancellation of program It is possible to correct the set program at any time by first pushing the relative programming button and then buttons 4 or 5. It is possible to cancel a program by changing the set time to "0. 00". By cancelling the working time you will automatically cancel the working end time and vice versa. Oven automatically switches off while the "AUTO" symbol flashes. Time cannot be corrected when the automatic working program is on. FEED CABLES TYPES AND SECTION TOTAL GAS MIXED UP TO 660 W MIXED UP TO 1320 W MIXED UP TO 2200 W MIXED UP TO 3520 W TYPE OF CABLE H05 RR-F H05 RR-F H05 RR-F H05 RR-F H05 RR-F INPUT 220 V~ 3x0, 75 mm2 3x1 mm2 3x1, 5 mm2 3x2, 5 mm2 3x4 mm2 GB TECHNICAL INFORMATION FOR THE INSTALLATION The installation and regulations shall be carried out by qualified technicians only. [. . . ] c) Assemble the tubeholder on the other end of the pipe putting in the seal G. Carry out the connection by a proper pipe in conformity with the regulations making sure that it is perfectly put on the tubeholder and tightened by a proper fixing clamp. b - Oven burners Remove the oven accessories, the lower plate and unscrew the back screw D, fixing the burner to the bottom of the oven, in order to take it away and enter the injector (fig. Once the proper injector has been assembled, remount the burner of the oven. Fig. 24 OVEN c - Grill burner It is possible to enter the injector taking away the burner fixed on the top of the oven by the front screw D (fig. [. . . ]