User manual MELICONI GUMBODY UNIVERSAL 5 SMART

[. . . ] They light up whenever a command is sent to the selected appliance. Number keys To select an external input terminal MUTE turns the volume on and off ON/OFF key to turn the selected appliance on and off Teletext keys To select the next (P+) or previous (P-) channel or programme Control the volume using +/­ FORWARD / REWIND functions for VCR and DVD VCR/DVD function keys: RECORD - PAUSE - STOP - PLAY or fastext functions To move around within the MENU or to control the BRIGHTNESS/COLOUR Confirm key Specific area for SET TOP BOX Impact-proof rubber casing PREPARE FOR USE Read these instructions carefully before programming your remote control! 1 FITTING THE BATTERIES Before programming and using the remote control, fit the batteries. The remote control requires 2 new AAA/LR03 batteries. Insert the batteries as shown: · Change the batteries if the light indicator starts to flash during use. · Make a note of the codes for your appliances on the adhesive label inside the battery cover in case you have to reprogramme your remote control. [. . . ] In this case consult the enclosed CD or the site www. meliconi. com/guide GLOBAL SEARCH REMOTE CONTROL PROGRAMMING This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming the remote control by means of the method described above. The quickest and easiest way to programme the remote control is by consulting enclosed CD or the website www. meliconi. com/guide. Turn on the appliance to be programmed: - if a VCR, insert a cassette - if a SAT or TER select a programme - if a DVD insert a DVD. Hold down the selection key for the appliance to be programmed for 5 seconds. Enter the code 0000; the selection key flashes more quickly to indicate that the remote control is ready for the search. Press and slowly release the ON/OFF key or PLAY for the VCR and DVD several times, stopping when the appliance responds correctly to the command. Three flashes indicate that the search operation has been completed correctly. or or or or 5 SEC. + + + or ADDITIONAL CHECK Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 2. To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY. N. B. The remote control exits programming mode and the light indicator stops flashing: · if no keys are pressed for 14 seconds · if a key other than ON/OFF or PLAY is accidentally pressed · if the end of the code search list has been reached. In this case consult the enclosed CD or the internet site www. meliconi. com/guide 3 CURRENT CODE DISPLAY To find out the code of your remote control, follow this procedure: 1. Hold down the selection key of the appliance whose code you want to know for 5 seconds. When the key is released it will start to flash; press and release the 1-/-- key within 8 seconds. After a few seconds, the light indicator communicates the code you are looking for by flashing the four numbers separately. Count the number of flashes; each series of flashes corresponds to one figure in the code. Make a note of the code on the adhesive label inside the battery cover for quick and easy future reprogramming. this operation cannot be interrupted and the remote control cannot therefore be used until the end of the 4 series of flashes. ENTERING THE CODE If you know the exact code with which to programme the remote control, enter it as follows: 1. Hold down the selection key for the appliance to be programmed for 5 seconds. When released, the selected key will start to flash, enter the code (e. g. [. . . ] Reset the remote control code, following the programming procedure. The code for your appliance make is not in the Code Book. To find the code with which to programme your remote control consult the enclosed CD or on-line guide at www. meliconi. com/guide. INFO-LINE If you have any queries about your UNIVERSAL 5 SMART remote control: · read this Instruction Booklet carefully - you will find an answer to most of your questions · consult the enclosed CD or our website where you will find the answers you need easily and quickly. WARRANTY: 2 years The warranty ceases to be valid if the product is tampered with or used incorrectly. Remote control type GumBody Model UNIVERSAL 5 SMART Purchase date / / Dealer's stamp The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. [. . . ]