Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL MODEL SW425
RESIDENTIAL SWING GATE OPERATOR
2 YEAR WARRANTY
Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL SW425 IS FOR USE ON VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR USE ON PEDESTRIAN PASSAGE GATES
TABLE OF CONTENTS
OPERATOR SPECIFICATIONS
Carton Inventory . . 4-5
WARNING
Mechanical
OPERATOR WARNINGS
UL325 Model Classifications . . 12
CAUTION WARNING WARNING Electrical WARNING CAUTION
When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of SERIOUS INJURY or DEATH if you do not comply with the warnings that accompany them. When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. [. . . ] Connect the red wire to the positive battery terminal and the black wire to the negative battery terminal (Figure 3). There are wires provided for connecting the low voltage burial cable from the transformer to the gate operator. Be sure that the positive and negative match the positive and negative of the charger. Connect the other end of the burial cable from the operator to the transformer. Be sure to match the positive and negative terminals of the charger to the positive and negative terminals of the battery (Figure 4). If possible, it is desirable to locate the charger out of the weather. Be sure the battery has been properly charged before putting into operation. Figure 3
Negative Terminal Batteries
SOLAR POWERED INSTALLATION
If the gate operator is solar powered, no power will need to be run into the machine. The ends of the wires are provided with connectors which can simply be plugged in (Figure 5). If necessary the panel may be mounted away from the gate operator to get it out of the shade and into more consistent sunlight. Similarly to the battery run, the solar operator comes with the battery wires disconnected. For both batteries, connect the black wires to the negative terminals and the red wires to the positive terminals (Figure 3). The wires have been labeled to make these connections easier to do.
Figure 4
Transformer
Wires from Operator
Solar Panel
Figure 5
Post Cement Coupling Post Hole Burial Cable
18" Reducer Coupling Strain Relief
To Operator
14
ADJUSTMENT
RIGHT/LEFT OPERATION
If the gate seems to be functioning in reverse, the Right/Left side operation switch may need to be flipped (Figure 1). One way to know if the operator is working in reverse is to try the sensitivity. If pressure is applied to the gate while it is closing, it should reverse and go open. If pressure is applied to the gate while it is opening, it should stop and remain stopped until activated again. If the gate operator responds differently than this, flip the Right/Left side operation switch. If the auto close timer function is turned on, this provides another way of knowing if the operator is working in reverse. If, when the gate gets closed, the operator automatically opens, the Right/Left side switch may need to be flipped the other way.
WARNING
To reduce the risk of SEVERE INJURY or DEATH, disconnect power BEFORE performing ANY adjustments.
CAUTION
Figure 1
LEFT/RIGHT SIDE OPERATION
SWITCH
Move switch up for right side installation and down for left side installation
AUTO CLOSE TIMER ADJUSTMENT
With the full systems capability control board there is the option of using the auto close timer which will close the gate automatically after it has opened. To turn this feature on, flip the auto close timer to the on position (Figure 1). To adjust the amount of time it takes for the gate to begin closing use a small screw driver to turn the adjustment "pot" clockwise for more time (45 second maximum) or counter clockwise for less time. It is recommended that if the auto close timer function is used, that there be additional safety equipment installed to prevent the gate from closing into a vehicle or pedestrian.
GATE SENSITIVITY ADJUSTMENT
This step is for sensitivity adjustments on the full systems capability control board. [. . . ] Limit Switch Kit Complete with: Hex standoffs, limit switches, screws and flatwashers. Primary and Secondary Arm Kit Complete with: Primary arms, swivel, hex bolts, locknut, hex nuts, flatwashers, lockwashers, pipes, coupling and disconnect arm. Radio Kit Complete with: Radio, antenna, cable extension kit, screws, flatwashers, lockwashers and nuts. ITEM 1 2 3 4 5 6 7 8 9 10 11 12
INDIVIDUAL PARTS PART # 13-40067 10-40137 20-40155 21-40074 23-40161 25-40083 25-40152 29-40071 29-40089 29-40095 29-NP712 K79-40056 K79-40098 DESCRIPTION Limit Nut Gate Bracket Motor, 12Vdc Transformer Limit Switch, SPDT Overload, 1. 5 amp Motor Breaker, 7 amp Resistor, 1 Ohm, 25W, Ohmite Sonalert Piezo Alarm Charger, Battery 12V . 5A Dual Stg Battery, 12V 7AH Control Board - Full System Control Board - Solar
K2 K74-40084
K3 K74-40045
K4 K74-40065
K5 K72-40146
K6 K74-40141
K7 K74-40031
K8 K74-40151
K9 K75-40132
K10 K74-19916
26
I L L U S T R AT E D PA R T S
K9
2
K5 K8
5 8
4 K1 3 K10 K2 K4
12 K3 K6
10
K7 6 9
11
27
WARRANTY POLICY
LIFTMASTER® TWO YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. [. . . ]