User manual LIFT-MASTER PASSPORT
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER PASSPORT. We hope that this LIFT-MASTER PASSPORT user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER PASSPORT
Detailed instructions for use are in the User's Guide.
[. . . ] All receiver units utilize the latest in Chamberlain® rolling code technology.
WARNING
Children operating or playing with a garage door/gate opener can injure themselves and others. Do not allow children to operate the door control push button or the remote control transmitters. Install the receiver (and all control push buttons) out of the reach of children and away from all moving parts of the door/gate hardware, but where the door/gate is visible.
ACCESS CONTROL COMPATIBILITY
The CPWR outputs a 26-bit or 30-bit Wiegand format compatible with Sentex access control systems.
Doc 6001535, Rev G Page 1 of 6
Setting the Switches
Before making changes to any of the DIP switches, power MUST be disconnected from the receiver (unplug the terminal block from J2 on the circuit board). [. . . ] NOTE: Mount receiver with 18" of space above the receiver for the antenna. Also, receivers should be installed at least 5 feet apart to avoid "cross-talk".
STEP 2: CONNECT THE ANTENNA
Screw on antenna clockwise and slide rubber boot down to meet o-ring (see Figure 7).
CAUTION
The outside of the antenna connector is not ground. If using an extension kit, do not allow it to contact a metal object.
1535F5
Figure 7: Antenna Attachment
STEP 3: CONNECT SIGNAL/POWER WIRES
Remove the terminal block from J2 on the circuit board. Connect wires from the CPWR 6-pin connector to the access control system. Refer to the access control system's installation instructions for appropriate wiring detail. A typical wire connection might resemble the following:
CABLE SIGNALS LED DATA 1 DATA 0 +12VDC COMMON (GND) SHIELD WIRE COLOR BROWN WHITE GREEN RED BLACK SHIELD
Mounting Holes (4 Corners)
J2
1535F4
NOTE: At power up, the CPWR will perform a system check and produce a series of LED flash sequences. This is normal.
To Access Control Circuit Board (Reader Port)
Figure 8: Signal and Power Connections
Doc 6001535, Rev G Page 4 of 6
Testing and Troubleshooting
STEP 1: CHECK THE POWER
Ensure that the red POWER LED is lit (see Figure 9). Voltage reading should be within the range of 9VDC 18VDC.
STEP 2: CHECK FOR RECEIVER OPERATION
The SIGNAL LED (refer to Figure 9) should be flickering continuously, indicating that the RF receiver circuitry is operating.
STEP 3: TEST THE TRANSMITTER/RECEIVER
Press the transmitter button previously set in step 4, page 3, within view of the receiver. If the DATA-yellow and VALID-green LEDs do not light, review the Setting the Switches and Connect Signal/Power Wires sections. If reception of the transmitter's signal is significantly reduced, there may be strong RF interference from other sources. Common sources of interference include fluorescent lights, neon signs, mercury vapor lamps, arc welders, and arcing power lines. Interference due to lighting can be limited by having an electrician wire a noise suppressor into the lamp, light, or sign circuit. NOTE: It may be required to press the transmitter button twice at first use. If the DATA-yellow and VALID-green LEDs flash repeatedly and simultaneously, the format settings may be incorrect (refer to Output Code Format).
WARNING
Call your local power company if interference is due to arcing power lines.
RECEIVER LED REFERENCE
(Refer to Figure 9. ) SIGNAL Red This LED, when lit, indicates that the receiver has detected the presence of RF energy. It is normal for this LED to flicker continuously while the receiver is powered up. DATA Yellow This LED indicates that the receiver recognizes the transmission data as coming from a Chamberlain® transmitter with Passport technology. [. . . ] The warranty period shown above applies only to the LiftMaster receiver with Passport technology). Since this is a manufacturer's warranty, not a dealer's warranty, installation, removal, and freight charges are not part of this warranty, nor shall the installer be held liable in any way for removal, repair or installation of the Passport system unless otherwise stated in a separate dealer's warranty. This warranty does not extend to systems or compartments that show evidence of damage caused by vandalism, acts of God (e. g. , lightning, flood), abuse, or unauthorized or improper service.
COPYRIGHT 2001, ALL RIGHTS RESERVED This document is protected by copyright and may not be copied or adapted without the prior written consent of LiftMaster. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER PASSPORT
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER PASSPORT will begin.