User manual LIFT-MASTER DC2000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER DC2000. We hope that this LIFT-MASTER DC2000 user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER DC2000
Detailed instructions for use are in the User's Guide.
[. . . ] DC2000 Back-Up Installation
SL3000ULTM & SL3000ULDMTM Step-by-Step DC2000 Installation
STEP 1
Bolt the DC2000 plate and guard to the operator chassis. Adjustment is required in Step 3.
for for SL3000ULTM models
UL
® LISTED 4K55
CLASS I, II, III, IV
STEP 2
A B C
Bolt the DC2000 control unit to the plate. [. . . ] (Automatic open or Manual open) Permanently wire optional controls according to label on control unit. (See back page) Adjust the sensitivity for the reverse sensor.
OFF
ON
CLASS I, II,
III, IV
ON
C D B D A
C
A
1 2 NC NC 2 1 NO 3 COM NO 3 COM
W4
J5
B
BACK -B K DC-BACKUP
SENSOR ALARM
D
POWER OVERLOAD
A C
SL3000ULTM & SL3000ULDMTM with Interlock Assembly Step-by-Step DC2000 Installation
STEP 1
Bolt the DC2000 plate and guard to the operator chassis. Adjustment is required in Step 3.
STEP 2
A B C
Bolt the DC2000 control unit to the plate. Red to Red and Black to Black.
STEP 3
A B C A
Remove interlock assembly from motor with 3 screws. Reattach interlock assembly.
Brown Red Green
B
Yellow Orange Purple
STEP 4
Unplug interlock wire from OmniControl board, cut the plug off and strip wires. Insert Red wire in J-20 socket 3 and Black wire into socket 4 of the DC2000.
STEP 5
A B C D
Remove the OmniControlTM board from the electrical box. Feed the green and purple wires to the limit box.
D
OFF
Existing Belt
A Interlock Assembly
DC2000 Control Unit Plate Bolts Plate
B A C
DC Motor
B A
C C
Guard
7 456
ON
W4
C A
123
B
Do not over tighten belt
B
SL3000ULTM
Use 4L 370 Belt
SL3000ULDMTM
Use 4L 400 Belt
Socket 3 & 4
STEP 6
A B C D
Reinstall the OmniControlTM board and make sure that the green and purple wires do not get pinched by the board. Plug in the DC2000 harness in the DC-BackUp J5 slot on the OmniControlTM board. Connect the red wire from the DC2000 harness into the top slot of the audio alarm plug. (DO NOT remove audio alarm wires) Connect the white wire from the DC2000 harness into the bottom slot of the sensor plug.
STEP 7
A B
Connect the purple and green wires to the limit switches. Make sure brown wire is in the "Common" connector on the limit switch.
STEP 8
A Top View of Limit Switch Box B
Set switch for the gate direction. (Open left or Open right) Select your mode of operation for the DC2000 unit. [. . . ] After such cancellation, the DC2000 will continue to operate in manual mode until 115 Vac power is restored.
1
6 345 2
7
4
5
OPEN CLOS E
Socket
3
4
Part # A1KX
Turn and "Hold" to Open Turn again and "Hold" to Close
"Optional Three-Button"
CENTER SAFETY EXIT
Interlock Assembly
OFF
ON
N. O.
3
4
Com
N. O.
SENSOR ALARM
2 1
4 4
Com
DC-BACKUP
W4 GBA
MS LINK
N. O.
SENSORS
Com
SYSTEM ON
TIMER 60 3
POWER OVERLOAD
OPEN
REVERSE SENSOR
ALARM SENSOR
1
3
OFF
OPEN LEFT
ON
OPEN RIGHT
MADE IN USA
"Optional Radio Receivers"
Push and "Hold" a Button to operate
1
3
1
3
EXIT
COMMAND PROCESSED
CENTER SAFETY
FIRE DEPT.
STRIKE OPEN
RADIO RECEIVER
GATE LOCKED
EXIT LOOP
SAFETY LOOP
CENTER LOOP
RESET MOTOR
OSE LOS CLOSE
STOP
12 VDC Back-up Radio Receiver
OmniControl Surge Suppressor
P/N Q410 Patent Pending
11 12 13
+
Class 2 Supply
24 Volts DC
DO NOT remove existing wires from the audio alarm or secondary protection sensor.
Part # 412HM
56 44
1
G
B
M/S Link
A
Center Loop
Safety Loop
Exit Loop
Fire Dept Key Switch
Strike Open Push Button
Radio Receiver
2 3 4
Jumper P2: to Momentary (M) Jumper P3: to 12 Volt
CAUTION Vac
Black 120 White Neutral Green Ground
J5
BACK -B CK J5 DC-BACKUP
SENSOR ALARM
CHASSIS GROUND
Red Wire White Wire Audio Alarm Wires
11 13 11 12
Button Three: Optional Accessories
Button Two:
1
Back-Up Operation (DC2000)
®
Button One: Normal Gate Operation (OmniControlTM Board)
2 3 4
Part # 412HM Part # 973LM
POWER OVERLOAD
For Technical Support and Ordering Parts: 1-800-528-2806
Green and Purple wires wrap behind board to the limit switches
24 VDC radio receiver to be used by OmniControlTM Board
DC2000 Harness
13 12 11 11
Push and "Hold" DC2000 Remote Button to Open Push again and "Hold" DC2000 Remote Button to Close
®
Radio Receiver +
Radio Receiver © 2004 The Chamberlain Group, Inc. All Rights Reserved
01-51128
845 Larch Avenue Elmhurst, Illinois 60126
TM
www. chamberlain. com [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER DC2000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER DC2000 will begin.