User manual LIFT-MASTER CPSII
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER CPSII. We hope that this LIFT-MASTER CPSII user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER CPSII
Detailed instructions for use are in the User's Guide.
[. . . ] When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. The sending eye (emitter with an amber indicator light) transmits an invisible light beam to the receiving eye (receiver with a green indicator light). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to full open position. [. . . ] · Attach bracket assemblies with 1/4"x1-1/2" lag screws (Figure 2). · Adjust right and left side bracket assemblies to the same distance out from mounting surface. Tighten the nuts securely.
1/4"-20 Lock Nuts
"C" Wrap Mounting Bracket with Slot Mounting Bracket with Square Holes
Figure 3 DOOR Track Installation Door Track Installation Procedure
· Discard slotted bracket. Drill 3/8" holes in each track and fasten securely with hardware (Figure 3).
Inside Wall Door Track 1/4" Lock Nuts Mounting Bracket with Square Holes
Drill 3/8" Holes "C" Shaped Wrap 1/4-20x1/2" Carriage Bolts
HARDWARE SHOWN ACTUAL SIZE
Screw #10-32x3/8"
Lock Nut #10x32
Lag Screw 1/4x1-1/2" Staples
Carriage Bolts 1/4"-20x1/2"
Lock Nut 1/4"-20
Figure 4 Alternate Wall Mount
Inside Wall Mounting Bracket with Slot Mounting Bracket with Square Holes "C" Wrap Sensor with wire Indicator Light Floor
Figure 5 Alternate Floor Mount
Inside Wall Sensor with wire Indicator Light Mounting Bracket with Square Holes Mounting Bracket with Slot Attach with concrete anchors (not provided)
"C" Wrap
Floor
2
Bell Wire
Secure Wire with Insulated Staples
Connect Wire to Commercial Protector Interface
Safety Sensor Beam 6" (15 cm) max. above floor
Invisible Light Beam Protection Area
Safety Sensor Beam 6" (15 cm) max. above floor
MOUNTING AND WIRING THE SAFETY SENSORS
· Insert the wire connector into each sensor and push until you hear a click. The white tab on the sensor should be flush with the back of connector. · Center each sensor unit in a "C" wrap with lenses pointing toward each other across the door. Finger tighten the wing nut on the receiving eye to allow for final adjustment. · For wiring connections, see following pages: CPS page 4 CPS-L page 4 CPSII page 5
Sensor
Figure 6
Wing Nut "C" Wrap Wire
Indicator Light
1/4-20 x 1-1/2" Hex Bolt
HARDWARE SHOWN ACTUAL SIZE 1/4-20x1-1/2" Hex Bolt Wing Nut
ALIGNING THE SAFETY SENSORS
· Power up the opener. Green indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct. If the receiving eye indicator light is not glowing steadily (and the invisible light beam path is not obstructed), alignment is required. · Loosen the receiving eye wing nut to allow slight rotation of unit. Adjust sensor vertically and/or horizontally until the green indicator light glows steadily. · When indicator lights are glowing steadily in both units, tighten the wing nut in the receiving eye unit.
3
CPS Wiring Connections
Commercial Protector Interface 24V
Common CDO Sensing Edge Input Sensor White To Sending Eye (Emitter) and Receiving Eye (Receiver) Sensor White/Black
WARNING CPS-L Wiring Connections for use with Solid State II (Logic Control Board Ver 2) CAUTION
Once eyes are connected it will be necessary to set DIP switch to Timer to Close mode (refer to "Activate Photo Eyes" instructions below).
Logic 2 Shown
White White/Black
TO ACTIVATE SAFETY SENSOR EYES
1. Starting with the door in the close position, run the door through one full open-close cycle to "Learn" the sensor eyes. [. . . ] NOTE: For non-solid state operators, if the door is stopped in a mid position, activation of the sensors will cause the door to open. CPS-L Only: If the sending eye and receiving eye indicator lights are both lit but interrupting the photo eyes does not cause the door to reverse when closing, refer to "To Activate Safety Sensor Eyes" on page 4.
6
Replacement Parts
CPS CPSII Commercial Protector Interface . . 001A5053-9
CPS / CPSII / CPS-L
How to Order Repair Parts
Our large service organization spans America. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER CPSII
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER CPSII will begin.