User manual LIFT-MASTER 90 F2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER 90 F2. We hope that this LIFT-MASTER 90 F2 user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER 90 F2
Detailed instructions for use are in the User's Guide.
[. . . ] F2 WIRING TYPE (K-LINE OPERATORS) CONVERSION
90F2 FOR MODELS: T, GT, J, H, GH, SD, GSD
APPLICATION
This modification is available to Model T, GT, J, H, GH, GSD and SD standard door operators with 24V control circuits (M). Required for use with 4-wire "fail-safe" type electrical edges. [. . . ] Proceed with limit switch adjustment per owner's manual.
WARNING CAUTION
WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution, disconnect electric power to operator BEFORE installing. ALL electrical connections MUST be made by a qualified individual.
WARNING
FIELD WIRING
OPEN CLOSE 1 2 STOP EXTERNAL INTERLOCK TO OPEN AND CLOSE 7 R FAIL - SAFE SAFETY EDGE
DIODE
TERMINAL BLOCK REMOVE JUMPER WHEN EXTERNAL SWITCH IS USED.
3 4 5
NOTE: The door will not close if safety edge or wiring is damaged. Do not apply power until after reading fail safe safety instructions.
10
G O. K.
BL 1 PHASE POWER IN L1 L2 L3
R N. G. TEST LIGHTS
L1 3 PHASE POWER IN L2 L3
GROUND
3 RADIO RECEIVER 2 1
R3 R2 R1
(OPTIONAL) AUX. ONLY Y 4 OP 3 P GY 5 OP 6 1 CL 2 BL P TO MOTOR BL Y GY 1 8 5 4 2 3 BK-BK 230V. BRAKE SOLENOID SOLENOID (WHEN REQUIRED) (WHEN REQUIRED) R3
POWER IN
BK-BK 115V. CONNECTION BK-BK
3PDT.
TO REVERSE MOTOR DIRECTION, INTERCHANGE PURPLE & GRAY WIRES.
BR W EXTERNAL INTERLOCK 5 HAND CHAIN SWITCH PRI.
3
STOP Y
BR 4
Y
Y 24 VAC. 14 OP 13
Y
(WHEN PROVIDED)
OR FOR DELAY ON REVERSE MOVE TO 3d OR OPEN 1 RADIO TO OPEN AND CLOSE R2 R1 OR Y TO OPEN AND CLOSE 7 4 WIRE FAILSAFE EDGE OR OR
IR
Y
OR OR 1 3i 3d 9 G O. K. C 10 GY
Y
R DIODE BL
10
P
2 CLOSE
P
IR
R 14 CL
P
P A2
CL
A1
P CLOSE L/S P N. C. (Instant Reverse) relay is wired normally open and is held closed when motor is not running. Optional timer to close will, after preset time, close the door whenever it is not fully closed and all open and safety devices are cleared. We recommend the use of 16 gauge or heavier wire for all control circuit wiring. [. . . ] BRAKE SOLENOID (WHEN REQUIRED)
BR O/L (WHEN PROVIDED) L2 BK POWER IN
L1 BK L1 BK
BR BR BR EXTERNAL INTERLOCK 4 MOTOR O/L OR HAND CHAIN O/L PILOT SWITCH Y OR BR Y OR BR 5 Y OR BR (WHEN PROVIDED) 14 OP 13 FOR DELAY ON REVERSE MOVE TO 3d OR OPEN 1 RADIO TO OPEN AND CLOSE R2 R1 TO OPEN AND CLOSE Y 7 Y C P N. C. SEC.
3 Y
STOP
OR
4 WIRE FAILSAFE EDGE R DIODE BL
10 GY 24 BL
2 CLOSE
P 14 CL R 13
P
P A2
CL
NOTE: Terminals R1, R2 and R3 are on optional external terminal block.
3
01-13410B
© 2006, The Chamberlain Group, Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER 90 F2
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER 90 F2 will begin.