User manual LIFT-MASTER 61LM
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LIFT-MASTER 61LM. We hope that this LIFT-MASTER 61LM user guide will be useful to you.
Manual abstract: user guide LIFT-MASTER 61LM
Detailed instructions for use are in the User's Guide.
[. . . ] Single-Button Remote Control
Model 61LM
2-Button Remote Control
Model 62LM
3-Button Remote Control
Model 63LM
Figure 1
Model 61LM Model 62LM Model 63LM
WARNING
(+)
Push Buttons
(0)
()
Push Buttons
Locating your code switches
Single-Button Remote Control: Slide the battery compartment cover back to access the code switches in the remote control (Figure 2). 2-Button Remote Control: The 2-button remote control has two push buttons (for button 1 and button 2), each activated by its own set of code switches. [. . . ] Slide back the battery compartment cover to access the code switches in the 3-button remote control (Figure 2).
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
CAUTION
AVERTISSEMENT ATTENTION
0 + 1 2 3 4 5
Figure 2
Model 61LM Single-Button Remote Control
1 2 2 3 3 4 4 5 5 6 6 6 7 7 7 8 8 8 9 9 9 0 + 1 0 +
Model 62LM 2-Button Remote Control
Code switches (1-9)
Code switches (1-9)
Model 63LM 3-Button Remote Control
1 2 3 4 5 6 7 8 9 0 +
Code switches (1-9) (Code switch #1 is dormant. )
To match or change the code in the remote control
Locate the code switches in both the new and the original remote controls, either by removing the case screw and cover or by sliding the battery compartment cover back. Place remote controls side by side as shown (Figure 3) and set switches in all remote controls to matching positions (+, 0, -). NOTE: Code switch #1 on the three-button remote control is dormant, when used with a single-button remote control. Set code switch #1, in the single-button remote control, to match the push button selected on the three-button remote control (Figure 1).
Figure 3
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 0 + 1 2 3 4 5 6 7 8 9 0 + 1 2 3 4 5 6 7 8 9 0 + 1 2 3 4 5 6 7 8 9 0 + 0 +
Match code switches (1-9) between old remote control and new remote control
Match code switches (1-9) between old remote control and new remote control
Match code switches (2-9) between old remote control and new remote control
Programming the opener
RED-1 WHT-2
+ 0 -- 1 2 3 4 5 6 7 8 9
H I G H N ORM
Replacing the remote control battery
WARNING
To prevent possible SERIOUS INJURY or DEATH: · NEVER allow small children near batteries. · If battery is swallowed, immediately notify doctor.
ORM
OR
RED-1 WHT-2
CAUTION
H I G H N
Locate the battery by sliding the battery compartment cover. Dispose of old batteries properly.
If your unit has a "Learn" button:
1. Press and release the "learn" button located on the back panel of the motor unit. [. . . ] Use a pen or screw driver to set the code switches on the back of the remote control to match the code switches on the back of the motor unit. Once the code switches have been set push the remote control button to activate your unit.
+ 0 1 2 3 4 5 6 7
+ 0 1 2 3 4 5 6 7 8
H I G H N
8
9
9
114A1224F
© 2006 The Chamberlain Group, Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER 61LM
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER 61LM will begin.