User manual KENWOOD DNX6160
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD DNX6160. We hope that this KENWOOD DNX6160 user guide will be useful to you.
Manual abstract: user guide KENWOOD DNX6160
Detailed instructions for use are in the User's Guide.
[. . . ] 6 7
After the Installation
After the installation, perform the Initial Setup by referring to the instruction manual. For safetyâs sake, leave the mounting and wiring work to professionals. ¢ Make sure to ground the unit to a negative 12V DC power supply. [. . . ] (DNX6960/ DNX6160/ DNX6020EX/ DNX6460BT/ DDX616/ DDX6046BT only) Bluetooth antenna unit
¤ CAUTION
Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. 11 5:36:01 PM
Connection
Ignition key switch
connect (red) and the battery ¤ If you(yellow) tothe ignition wire(ground), you may wire the car chassis cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. ACC
A B A B C
Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) Antenna Cord FM/AM antenna input
Car fuse box Car fuse box (Main fuse)
C
Battery
Connect â detectionto the vehicle's parking brake switch harness. Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor. Reveres sensor wire (Purple/White)
Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote
Steering remote control wire (Light Blue/Yellow)
â
To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. Dimmer control wire (Orange/White)
To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Mute control wire (Brown)
â
Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. Motor antenna control wire (Blue)
Power control wire (Blue/White)
â
4 |
DNX SERIES/ DDX SERIES
If no connections are made, do not let the cable come out from the tab. 11 5:36:02 PM
Bluetooth Microphone (Accessory 2) (see page 8)
GPS Antenna (Accessory 3) (see page 8)
FUSE ( 15A )
Accessory 1
REVERSE
REMOTE CONT
STEERING WHEEL REMOTE INPUT
White/Black White Gray/Black
+
To front left speaker
ILLUMI
Gray
MUTE
+
To front right speaker
Green/Black Green Purple/Black
+
To rear left speaker
ANT. 5Ï)
To TMC Tuner GTM10 (optional accessory) (DNX6960/ DNX6160/ DNX6020EX/ DNX5160 only)
Accessory 9
When connecting the TMC Tuner GTM10 (optional accessory), put the cable clamper (accessory 9; DNX6960/ DNX6160/ DNX6020EX/ DNX5160 only) to the back of this unit first, and then wire the cable through the clamper. Rear Preout ⢠Audio left output (White) ⢠Audio right output (Red) Front Preout ⢠Audio left output (White) ⢠Audio right output (Red) Subwoofer Preout ⢠Audio left output (White) ⢠Audio right output (Red)
6 |
DNX SERIES/ DDX SERIES
B54-4761-00_00_DNX6-5_K_En_r1. [. . . ] Â
Make sure that the unit is installed securely in place. Engage the catch pins on the removal tool 8 and remove the two locks on the lower level. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD DNX6160
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD DNX6160 will begin.