User manual CANDY CMD 95
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY CMD 95. We hope that this CANDY CMD 95 user guide will be useful to you.
Manual abstract: user guide CANDY CMD 95
Detailed instructions for use are in the User's Guide.
[. . . ] For air evacuation to the outside, follow all the other instructions given on the "Warnings" sheet. Prepare the power supply within the telescopic flue (for the electrical connection, follow all the other instructions on the "Warnings" sheet). As previously specified in the chapter "Warning" remember there must be a minimum of 650 mm between the bottom edge of the hood and the top of the stove. before installing the hood , check that the brackets fixing screws (Fig. [. . . ] Secure the metal brackets (A) to the wall using the screws and plugs (brackets, screws and plugs are all supplied with the unit). Now fit on the hood using the relative rectangular slots situated at the rear of the appliance. Adjust the horizontal position, shifting the hood to the right or left as needed lining it up with the wall units. If the height of the hood also requires adjustment, use the special regulation screws (B) (supplied). Once regulation has been completed, finish securing the hood with 2 more screws (C): mark the points for the 2 holes on the wall, remove the hood and drill (8mm diameter holes); then use the plugs and screws to complete installation. 6: The rear metal panel must be fixed to the wall in the upper part of the hob. Rest the lower edge of the panel behind the hob and fix the upper edge to the wall by means of the two holes in the panel itself, inserting the supplied screws and screw anchors (A). The appliance should be fixed to the rear panel in the same way as wall fixing, using the supplied hood brackets and the screws and screw anchors supplied with the panel (B). Fixing the telescopic flues: Using the supplied screws and screw anchors, fix the upper flue bearing bracket to the ceiling and/or wall, checking that it is aligned with the hood (Fig. Prepare the telescopic flues, remembering that their final position must be that illustrated in Fig. 8 (turn upside down the upper flue so that the air disposal gratings are downwards). For fixing to the wall refer to the instructions for the ducting version (see point 2, 3), then continue with the instructions below. Fixing the telescopic flues: Using the supplied screws and screw anchors, fix the upper flue bearing bracket to the ceiling and/or wall, checking that it is aligned with the hood (Fig. Prepare the telescopic flues, remembering that their final position must be that illustrated in Fig. 8 (turn upside down the upper flue so that the air disposal gratings are downwards). Use a flexible pipe and lock it to the air evacuation pipe of the hood with a metal hose clamp - Fig. Connect the hood to the external motor using the special terminal block (Fig. 18): remove wire clamp A and lid B from the wiring junction box; fix the connecting wire of the external motor to terminal C; then replace wire clamp A and lid B on the wiring junction box; the other end of the wire is secured to the terminal block on the external motor. Installation is now complete and the grease filters can be reassembled. Depending on the model, the appliance is equipped with the following commands: Commands shown in Fig. 20: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot lamp comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the corresponding pilot lamp flashes to indicate that the grease filters must be cleaned and the charcoal filters replaced. To restart the hour counter (RESET), hold the button A pressed down for about 1" (while the pilot lamp is on). [. . . ] To restart the hour counter (RESET), hold the button A pressed down for about 1" (while the pilot lamp is on). Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down for about 1", the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button C: drives the motor in second speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button D: drives the motor in third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY CMD 95
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY CMD 95 will begin.