User manual ADCOM GTP-760

[. . . ] It is particularly important that you connect your preamplifier to your amplifier while the amplifier and preamplifier are unplugged and your other equipment is turned off. This will protect your equipment from potential short circuits that may occur during installion. In addition, it is important that you allow for adequate ventilation around your preamplifier and other equipment, since excessive heat buildup can shorten the life of any electronic product, including the preamplifier. Once you have correctly connected your new preamplifier to your other components, you should be able to enjoy many trouble-free years of performance. [. . . ] If you have an ADCOM GCD-750 player, this command will cause an idle CD to play. If your GTP-760 is on you will also notice the display does not respond to this command. The button description that follows distinguishes the function of each button dependent on the page the remote is in. The remote is shipped from the factory with ADCOM commands saved under the main, tuner, DVD, and CD pages, and with important GTP-760 functions such as volume saved under each page. The ADCOM universal remote controller is preset to operate all GTP-760 functions (main and tuner device mode) and most ADCOM DVD and CD player functions. Four AAA (R 03) batteries should be fitted in the battery compartment at the rear of the remote control. When replacing batteries, check that they have been put in correctly, as indicated on the base of the battery compartment. 2. 3 Remote Features [32] Main Button In all modes, button provides access and control to the GTP-760. [33] Source Selection Buttons These buttons switch inputs on the GTP-760, making the selected source active. They also can change the functions of other buttons on the remote controller. [34] Power Button In all modes, this is pre programmed to toggle on/standby the GTP-760 power. [35] Mute Button In all modes, this button is pre programmed to mute outputs of device. Any adjustment of the volume control while in the mute mode will release the muting. [36] Volume Up & Down Buttons In all modes, these buttons change the master volume setting of the GTP-760. In all modes except main, they can be reprogrammed with new commands. [37] Tape & Aux Buttons In main mode, these are similar to the source selectors described above but they switch only GTP-760 inputs. They do not automatically change the functions of other remote buttons. [38] Dynamic Range Button The d. range button, which can be used only in combination with a Dolby Digital source, incrementally reduces the audio track's dynamic range in four steps to allow for comfortable listening under a variety of conditions. 2 backlight dim selects 880 codes selects 880 dvd input selects 880 vcr input selects 880 cd input selects 880 video 1 input selects 880 video 2 input selects 880 video 3 input selects 880 tuner toggles 880 power on/off selects 880 tape input selects 880 aux input toggles 880 audio mute toggles 880 night mode 880 master volume up 880 master volumer dn programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable backlight programmable Code 195 135 134 136 131 132 133 137 128 138 139 130 223 213 209 Function: Video 1 selects 880 codes selects 880 dvd input selects 880 vcr input selects 880 cd input selects 880 video 1 input selects 880 video 2 input selects 880 video 3 input selects 880 tuner toggles 880 power on/off selects 880 tape input selects 880 aux input toggles 880 audio mute toggles 880 night mode 880 master volume up 880 master volumer dn programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable backlight programmable Code 195 135 134 136 131 132 133 137 128 138 139 130 223 213 209 ADCOM GTP-760 Owner's Manual | 29 Custom Code: 1AE5h Code Type: NEC Carrier Frequency: 38kHz Buttons main DVD VCR CD vid 1 vid 2 vid 3 tuner power tape aux mute d. range Vol Vol Function: Video 2 select play menu pause stop 1 2 3 4 5 6 7 8 9 0 +10 enter 7. 1m2 Dolby DTS stereo DVD-A SACD 2-ch random repeat ch. 2 backlight dim selects 880 codes selects 880 dvd input selects 880 vcr input selects 880 cd input selects 880 video 1 input selects 880 video 2 input selects 880 video 3 input selects 880 tuner toggles 880 power on/off selects 880 tape input selects 880 aux input toggles 880 audio mute toggles 880 night mode 880 master volume up 880 master volumer dn programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable backlight programmable Code 195 135 134 136 131 132 133 137 128 138 139 130 223 213 209 Vunction: Video 3 selects 880 codes selects 880 dvd input selects 880 vcr input selects 880 cd input selects 880 video 1 input selects 880 video 2 input selects 880 video 3 input selects 880 tuner toggles 880 power on/off selects 880 tape input selects 880 aux input toggles 880 audio mute toggles 880 night mode 880 master volume up 880 master volumer dn programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable programmable backlight programmable Code 195 135 134 136 131 132 133 137 128 138 139 130 223 213 209 30 | ADCOM GTP-760 Owner's Manual Buttons Function: Notes Data Code Macro 1 Function: Notes Macro 2 Function: Notes Macro 3 Function: Notes Macro 4 Function: Notes ADCOM GTP-760 Owner's Manual | 31 2. 5 Programming the GRC-810 Remote As you've already seen, the GRC-810 is pre programmed to control ADCOM's GTP-760 tuner preamp and the GCD750 CD and GDV-850 DVD players. In addition, it has seven "component memory banks" available so you can program the remote to learn commands for your DVD player, satellite box, laser disc player, VCR, etc. This lets you use one remote controller for your entire system. the appropriate source selector button. For example, if you're teaching your ADCOM remote commands for your video 1 source, press the vid 1 source selector first. You can "teach" your remote new commands for any function button (except backlight) after you've selected DVD, VCR, CD, vid 1, vid 2, vid 3 and tuner. Place the source component's remote "head to head" with the ADCOM remote. Press the ADCOM remote's appropriate source selector and select buttons simultaneously. Hold both buttons until the status LED turns orange and the source selector button glows red. Decide which function button on the ADCOM remote you want to learn a new command. The orange status LED will begin to flash and the source selector LED will go out. [. . . ] · Weak signal · Multi-path signals or interfeence from another station · Interference from other electrical sources - computers, games consoles · Interference from fluorescent lighting or electrical motor · Station signal too weak. · Station not transmitting RDS data Possible Solution · Check if AC lead is plugged in and power switched on · De-select Tape Monitor mode · Switch off Mute · Turn on the Power Amplifier · Check connections and speakers · Check leads and connections · Select appropriate Surround mode (large or small) No sound on one channel No sound on surround channels · Select a Surround Mode · Test system with stereo or Dolby Surround material · Check speakers and connections · Increase surround volume level · Select appropriate Center mode (large or small) · Check speaker and connection · Increase center volume level · Connect digital output of source to GTP-760 · Check source material · Check connections to all speakers in the system · Check or replace batteries · Remove obstruction · Place unit away from direct sun, reduce amount of ambient light No sound on center channel "Dolby Digital" OR "DTS" autodetection function does not work Weak bass/diffuse stereo image Remote control handset not working No sound with tuner · Check antenna connections to preamplifier · Re-tune or switch off FM Mute · Check station tuning. Switch off or move the source of the electrical noise · Check station tuning. Adjust or replace antenna · No remedy Noise, hiss on AM and FM Distortion on FM Whistles or buzzes on FM & AM Whistles or buzzes on AM No RDS name (PS) ADCOM GTP-760 Owner's Manual | 49 Caring for your GTP-760 Great care has been taken by ADCOM to ensure that your amplifier is as flawless in appearance as it is electronically. [. . . ]